Brighter pavers with clean, tight, freshly sanded joints
Paver Cleaning and Joint Sand in Fleming Island
Call (904) 682-0688 for a free paver cleaning estimate.
- Brings out deeper paver color
- Fresh joint sand helps lock pavers in place
- Gives weeds less room to grow
- Makes the surface easier to keep clean
- Free estimate, no obligation
Request a Free Estimate
Free, no obligations.
What does paver cleaning do for your home?
Paver cleaning lifts algae, dirt and stains off the surface so your pavers look brighter and are safer underfoot. Fresh joint sand then helps lock them in place and gives weeds less room to grow. A side walkway that had gone green starts to look like part of the property again. To get a free estimate with no obligation, call (904) 682-0688.
Cleaning is the first stage of any sealing job, and it can also be done on its own. Shaded areas and spots hit by sprinklers tend to go first. The same property can have one clean driveway and one badly stained side walkway. Point out the worst areas when you request a quote.
Fleming Island Paver Sealing Is Proud to Serve the Fleming Island Area
What is included in paver cleaning?
Pavers need cleaning when you see dark streaks, green growth in shaded corners, weeds in the joints or sand washing out after storms. Algae is the most urgent of these on walkways and pool decks, since a slick surface is a safety concern for anyone walking on it. To reach a contractor who handles this work, call (904) 682-0688.
Cleaning alone restores the surface but offers no added protection, so algae and staining can return on their own schedule. Sealing after cleaning adds a coat that makes the surface easier to keep clean and can deepen its color. It also becomes a repeat job, since companies commonly quote a sealer life of two to five years. Tell the contractor which you prefer, or call (904) 682-0688 to talk it through.
A freshly washed surface has to dry before sealer goes on, so the two stages are usually separated by some waiting time. Unilock, a paver manufacturer, says that can take a few hours in warm sun or about a day in cool shade. Rain in the forecast can move the schedule. Ask how the contractor handles that when you request a quote.
Washing technique matters as much as the product. Too much pressure can pull sand out of the joints and scar softer pavers, which is why re-sanding normally follows a wash. Ask what pressure and nozzle the contractor uses and whether the cleaning solution is safe for nearby plants and pool water. Have other questions about your surface? Call (904) 682-0688.
Here is a common myth: more pressure means a cleaner surface. It does not. Western Interlock, a paver company, says about 1,500 PSI is the right target and tells homeowners to use the widest wand they have. Family Handyman warns against spraying into the joints, since that knocks the sand out. A rushed wash at full blast can leave swirl marks and empty joints, which means more work to fix them. Ask about PSI and nozzle size before you request a quote.
A white, chalky film is a different problem from dirt. It is called efflorescence, and it comes from natural salts in the materials. Unilock says it is temporary and does not weaken pavers, though it can take two to three months or up to a year to fade. It must be gone before any sealer goes on. If you cannot tell whether a white film is efflorescence or old sealer, point it out when you call (904) 682-0688.
How often should pavers be cleaned? Family Handyman suggests once a year, preferably in spring. Shaded walkways and sprinkler spots around Fleming Island can need attention sooner, while an open, sunny driveway may hold up longer. To set a schedule that fits your property, call (904) 682-0688.
Pre-treatment
A cleaning solution loosens algae and organic staining before washing.
Washing
The surface is washed in sections. Technique matters, since too much pressure pulls sand from the joints.
Joint sand
Sand goes back into the joints after the pavers have dried, which helps lock them in place.
Optional sealing
Sealer can follow once the surface is fully dry. See the sealing guide.
Paver surfaces that get cleaned
Driveways
A driveway takes tires, oil drips and the most sun on the property. Cleaning here is about keeping the color even and the joints full, which helps the pavers stay locked under the weight of a car.
Pool decks and lanais
Pool decks stay wet, and splash water and bare feet wear them in their own way. Cleaning around a pool should leave a surface that still drains and does not turn slick.
Patios
Patios often sit in shade, so algae gets started early and stays longer. Cleaning on a patio focuses on getting those green areas clean and slowing their return.
Walkways and entries
Walkways are narrow, close to the landscaping and easy to stain with soil and irrigation runoff. Cleaning near an entry makes the first thing a visitor steps on look cared for.
5 common paver problems in Fleming Island
1. Fading from full sun
Florida sun washes the color out of unprotected pavers, and driveways with no shade go first. Cleaning brings back what color is left, and sealing afterward slows the fading.
2. Green growth in shaded corners
Fleming Island has heavy oak cover and humid air, so shaded corners and north-facing walkways grow algae. Left alone it gets slick, which is a concern on a pool deck or front walk.
3. Joint sand washing out
Heavy summer rain carries sand out of the joints. Once it goes, pavers can shift and weeds move in, so new sand goes back before any sealer goes down.
4. Sprinkler stains
Irrigation that hits the same area every day leaves marks along edges and lower walls. Well water can make it worse. Those marks need treating before they are sealed in.
5. Cloudy or peeling old sealer
Old sealer can turn cloudy or lift when moisture is trapped under it. It has to be dealt with first, and a water-based product cannot go over a solvent-based one.
Paver cleaning pricing in Fleming Island
Some companies publish cleaning separately, with one Jacksonville company listing rates from $0.22 per square foot. At that starting rate, a 600 square foot driveway would begin around $132 and a 1,000 square foot pool deck around $220. Compare what is included, because joint sand and repairs are often priced apart from the wash. For a price on your property, request a quote. The estimate is free, with no obligation.
If you plan to seal as well, ask for one combined price. Northeast Florida companies commonly publish $1.50 to $2.50 per square foot for the full clean, sand and seal. Need help comparing the two? Call (904) 682-0688.
Planning to protect the surface too? Read about sealing your pavers, or check the areas we serve around paver sealing in Fleming Island.
| Paved area | Cleaning from | Clean, sand and seal |
|---|---|---|
| 300 sq ft | $66 | $450 to $750 |
| 600 sq ft | $132 | $900 to $1,500 |
| 1,000 sq ft | $220 | $1,500 to $2,500 |
Cleaning column uses one Jacksonville company's published starting rate of $0.22 per square foot. Sealing column uses the $1.50 to $2.50 Northeast Florida companies published as of November 2026.
Why choose us for paver cleaning?
One contractor, not a bidding list
Your request goes to one independent company that covers your area. That means you will not get a run of calls from several businesses chasing the same driveway.
No cost to homeowners
Using this website is free. Any price you pay is agreed directly with the contractor, and you are under no obligation to accept it.
Local pricing up front
You can see what Northeast Florida companies publish per square foot before you speak with anyone, so the first number you hear has context.
You stay in control
You decide whether to hire the contractor. See what to look for in a contractor, get the price in writing and take the time you need.
Contact Us Today for a Free Estimate
Send one request and hear from one independent contractor.
Free, no obligations
How the paver cleaning process works
1. Inspect the surface
The contractor walks the pavers and checks for sunken sections, stains, old sealer and how water runs off before pricing the cleaning job.
2. Clean it
Algae, dirt and residue come off first, in sections, using a pressure that leaves the joints intact.
3. Refill the joints
Once the surface has dried enough, fresh sand goes into the joints so the pavers lock together again.
4. Let it dry and apply
Sealer only goes on a dry surface, so timing follows the weather. It goes on by spray, roller or both in the finish you picked.
5. Walk it with you
The contractor shows you the finished area, explains how long to stay off it and tells you when it will likely need another coat.
Frequently Asked Questions
How much does paver cleaning cost in Fleming Island?
One Jacksonville company lists cleaning from $0.22 per square foot, so a 600 square foot driveway would begin around $132. Compare what is included, because joint sand and repairs are often extra.
Can I pressure wash my paver patio?
Yes, if you keep the pressure down. Western Interlock, a paver company, puts the target near 1,500 PSI with the widest wand you have. Test a hidden corner first and do not spray into the joints, since that knocks the sand out.
Can I use Dawn dish soap to clean my pavers?
Yes, for light dirt. Family Handyman's hand-washing method mixes Dawn into a bucket of water. Scrub with a stiff plastic brush, since Unilock warns that wire brushes can leave rust marks. For heavier growth, ask a contractor which cleaner they recommend.
Should pavers be cleaned before sealing?
Yes. Sealer traps whatever is on the surface, so algae and stains need to come off first.
How much does it cost to clean and seal pavers?
Northeast Florida companies commonly publish $1.50 to $2.50 per square foot to clean, sand and seal. A 600 square foot driveway would land around $900 to $1,500. Repairs and stripping old sealer usually cost extra.
Why do my pavers keep turning green in Fleming Island?
Shade, humidity and sprinklers keep the surface damp, which is what algae needs. Trimming back plants and adjusting irrigation helps, and sealing can make the surface easier to keep clean.
What is the white film on my pavers?
It is most likely efflorescence, a powdery deposit from natural salts. Unilock says it does not weaken pavers. It should be gone before any sealer goes on.
How often should pavers be cleaned?
Once a year is a good starting point, and Family Handyman suggests spring. Shaded walkways and sprinkler spots around Fleming Island can need attention sooner.
Can I clean pavers with bleach?
Yes, if you dilute it. Hunker's method mixes half a cup of bleach into a quart of warm water, and warns that a strong mix can lighten pavers or leave them splotchy. Keep it away from grass and plants, since bleach kills them.
How do you clean dirty pavers?
Start with water and dish soap, a stiff plastic brush and a hose. Scrub small sections and rinse as you go. Algae, deep stains and worn joints around Fleming Island usually call for a contractor with the right cleaner and fresh joint sand.